Nominal output voltage Minimum output voltage Maximum output voltage Maximum continuous output current limited by PTC When operating as in input: Selectable encoder output ppr. The motor can be connected directly to the MotiFlex e or through a motor contactor M-Contactor. MotiFlex e – Powering machine innovation. To select the correct filter, see section 3. Page – Motor output rating adjustment –
|Date Added:||14 September 2010|
|File Size:||45.26 Mb|
|Operating Systems:||Windows NT/2000/XP/2003/2003/7/8/10 MacOS 10/X|
|Price:||Free* [*Free Regsitration Required]|
The Command window can be used send immediate Mint commands to the MotiFlex e Performing Test Moves – Continuous Jog www.
Servo Systems Co. | Baldor | MotiFlex e
UV detector amplifier, purpose built, V. If the node in question does not conform to DS or DS and is not a Baldor CANopen node, communication is still possible using a set of general purpose S100 keywords. The RS interface could be damaged if a Ee100 plug is accidentally inserted while the drive is powered. The power supply module within all MotiFlex e models provides rectification, smoothing and current surge protection.
If you are using a motor with EnDat feedback, are not using a Baldor motor, or need to enter the specification manually, select the I would like to define a custom motor option.
The DC bus voltage is then switched by a power module to create the UVW output waveforms that drive the motor. HOME To set the acceleration rate for the homing profile.
Ac Power Cycling 3. If it is connected to a hub shared by other USB devices, communication could be affected by the activity of the other devices. On the left of the help window, the Contents tab shows the tree structure of the help file.
Mechanical Installation 10 mm 0. Optimizing The Velocity Response www.
Fieldbus modules for MotiFlex e100 drives
Each switch has 16 positions, allowing selection of the hexadecimal values 0 – F. Plated copper busbars are required to allow the DC bus voltage to be shared between neighboring MotiFlex e drives. In some applications, these parameters may need to be fine-tuned to provide the exact response that you require. The following sections describe the two main tuning issues and how to correct them.
Ac Input And Regeneration Resistor Output Wiring The installation methods shown in Figure 7 will improve the reliability of the system, reduce troubleshooting time, and optimize the EMC electromagnetic compatibility mottiflex of the control system.
A wide range of devices can be supported. If you do have a problem, read this section first. Using The Commissioning Wizard 6. If any phase is lost, the MotiFlex e will immediately trip and disable, reporting a phase loss error error In the information pane, click Scan.
SMS Machine Automation – ABB MicroFlex e Servo Drive
Bottom Panel Connectors www. This section describes the mechanical and motiflxe installation of the MotiFlex e in the following stages: Opto-isolated 24 V PNP. For safety reasons and UL compliance, they will become open-circuit in the event of failure. Limited Warranty For a period of two 2 years from the date of original purchase, Baldor will repair or replace without charge controls and accessories that our examination proves to be defective in material or workmanship.
See the Mint help file for further details. There is only a small amount of overshoot and very little zero-speed noise. MotiFlex e is a versatile drive with four frames sizes and nominal currents from 2. These filters also prevent high frequency signals from being transmitted back onto the power lines and help meet EMC requirements.
Motion controller, Baldor, MotiFlex e100, S/N: U1010290068, unused. S/No U1
This removes the need for manual fine-tuning of the system, although in some critical applications this still may be required. If you are using a Baldor Motor, the catalog number or spec. Selectable encoder output ppr. If you intend to send a third party to collect your goods on your behalfyou need to send them with a copy of your winner’s e-mail along with a photocopy of your photo ID and signed note of authority permitting staff to release your purchases to the third party.